3DP TPM Resin-cleaner 1 L

TPM RESIN-CLEANER, la solution de nettoyage avancée pour le post-traitement, 1 litre correspond avec produits de Formlabs

22.90 CHF

Incl. T.V.A. , plus

de	Prix unitaire / Pcs. (1,00 Pcs.)
5	21.65 CHF*
10	20.55 CHF*

Pcs.

108 Pcs. En stock
Délai de livraison calculé environ: 1 jours ouvrables pays étrangers

numéro d'article: 3DP-2757
GTIN: 8000005553138
HAN: 3DP-2757
Catégorie: Reinigung
Fabricant: 3d-printerstore

la description
Commentaires
MSDS (1)

3d-Printerstore.ch RESIN-CLEANER 1 liter

Our TPM Resin Cleaner is a high-quality European product produced by 3D-Basics.com that functions as an IPA (Isopropyl alcohol) alternative and has a lot of advantages

TPM Wash Solvent (Tripropylenglykolmonomethylether) is a non-flammable, low odour solvent that can be used to clean and dissolve uncured resin on stereolithography (SLA) 3D printed parts. TPM has a lower evaporation rate than IPA and washes about three times as many parts as IPA before needing to be replaced.

TPM is not currently certified for use with Formlabs biocompatible resins.

TPM is compatible with the Formlabs Finish Kit, Form Wash, and Form Cure.
For a detailed workflow, visit support.formlabs.com.

Instructions

Always wear gloves when handling TPM
Submerge the Model in the Resin Cleaner for 10-15 minutes and shake/move it every 2 minutes to help loosen the uncured Resin. If you use a ultrasonic cleaner or Cleaning Station the process will be much faster.
Check from time to time if all uncured Resin has been dissolved. If you are satisfied wash the product with water to remove any excess Resin and Resin Cleaner
For removing uncured Resin from SLA or DLP printed parts fill your cleaning vessel with the amount specified by the manufacturer. To minimize waste, it´s suggested to pre-clean the parts before placing them in the cleaning vessel to expand the lifespan of your fresh TPM. This can be done in a separate container with either "dirty" TPM from previous cleaning cycles or low evaporation cleaners such as DPM, TPM or PGDA.
Place the finished print in the cleaning vessel and clean the parts for at least 5 min. or according to the material manufacturers guidelines. After the cleaning cycle, wash the DPM coated part with water, let the model dry and check for a tacky surface, repeat if necessary, till the surface is not tacky anymore. If it´s still tacky replace the TPM.
Cure the model according to the instructions of your Resin. Resin Cleaner can be used multiple times, replace if the cleaning performance decreases.

This product is not labeled as dangerous according to Regulation (EC) No. 1272/2008.

General precautions

Keep out of reach of children.
Avoid breathing dust/fume/gas/mist/vapours/spray.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Store in a well-ventilated place. Keep container tightly closed.
Dispose of contents/container in accordance with local/regional/national/international regulations.

Technical Data

Chemical colour clear
Odour typical solvent
CAS Number 25498-49-1
Chemical Type Solvent Density 0.96 g/cm3 (20°C)

Disposal of TPM
TPM and container as well as rinsing water need to be disposed of at an appropriate waste treatment site.

Description	Test method	Value
Flashpoint	ASTM D 3828	75°C (1013hPa)
Boiling point		189,6°C (1013hPa)
Self-ignition temperature		207°C (1013 hPa)
Density at 23°C	MVPF 18	0,9539 g/cm3 (20 °C)